Åpen semitrailer med presenning

KRONE SDP 27*Mega*BPW*LiftA*StaplerH

VIN: WKESD00000715240

Distance from kingpin to center of support device: 2,267 mm
Unladen fifth wheel height: 980 mm
Double-T longitudinal and center beams, as well as
Crossbeams and outriggers welded together
Outer frame with
Multilock outer frame, universal load securing option every 100 mm
Front overall height: 80 mm (incl. floor and fifth wheel plate)
2" kingpin (corner dimension: 2,040 mm)
Rear underrun protection device according to EC directive,
for cargo box length: 13,620 mm i. L.
for cargo box width 2,480 mm i. L.
3 axles, each with a load capacity of 9,000 kg
Aggregate distance = 7,900 mm
Wheelbase: 1,310 / 1,310 mm
with center centering
BPW axles, 19.5", with air suspension (total stroke 260 mm)
and disc brake (ET 120)
Brake disc with a diameter of 370 mm
Tire size 6-ply, 435/50 R 19.5,
with lifting and lowering system, incl. automatic
ride height adjustment
load-dependent, fully automatic electronic
lift axle control for 1st axle
manual function on control console for forced lifting
(=starting aid according to Directive 97/27/EC) and forced lowering
Preparation of the lift/trailing axle(s) for operation
from the tractor unit (without tractor unit installation),
according to the selected connector(s) for light connection,
for control via
Note: The vehicle does not operate in the
BO power circuit when the 1st axle is lifted! The lift axle may only be used as a starting aid according to
Directive 97/27/EC!
Caution: reduced ground clearance in the area of the lift axle!
Loading height restricted by pallet stop
Cargo box width in the area of the pallet stop
reduced to: 2,460 mm i. L.
Supply and installation of a rear forklift holder, suitable
Chjdpfx Aszr Dkzeicea
for Palfinger piggyback forklift (incl. forklift pockets, underrun protection according to ECE-R58 and 2 pieces of counter holders for safety chains on the outside)
Tire size, piggyback forklift max.: 23"
Design of the mounting bracket: pole holder
Dimensions of the support rails: 100 x 100 x 10 x 1500 mm
Dimensions of the forklift pockets: 200x100x5x1200 mm
Center distance of the forklift pockets: 380 mm
Width of the folded-down underrun protection: 1340 mm
Forklift pockets flush with the rear crossmember.
Rear socket: 15-pin DIN ISO 12098
uneven load distribution!
Type: BO 13620
30 mm thick, waterproof floor panel, cut surfaces
sealed all around, continuous, waterproof bonding
between chassis and floor panel with permanently elastic high-performance adhesive. Strength according to DIN EN 283, for floor loads up to max. 7,000 kg forklift axle load.
Tear plate inserted in the floor panel at the rear (4x450mm)
Type: AB 13620 AGG Dimensions 13,620 mm i. L. x Width i. L.
see side rails
Aluminum universal side rails, continuous, for the attachment of
sliding tarpaulin and sliding side rails
Edscha sliding tarpaulin cover (175) with plastic joints,
overall height 175 mm, slope 0 mm, designed for the
transport of grid boxes according to DIN 15155
Height i. L. bottom edge of the side rail on the front side: 2,860 mm
Height i. L. bottom edge of the side rail on the rear side: 2,860 mm
Height i. L. bottom edge of the crossbar in the middle: 3,000 mm
Loading height in the rear portal: 2,845 mm
unladen overall vehicle height at the highest point approx. 4095 mm
hydraulic lift roof with 500 mm total lift,
can be raised separately on 4 corner posts
Overall height at the front can be lowered by 150 mm from the highest driving position (basic position) in 50 mm increments, reduced roof lift: 350 mm
Overa

Annonsen ble oversatt automatisk. Oversettelsesfeil kan forekomme.