Lavbygd semitrailer

FAYMONVILLE Multimax Satteltieflader (1+2) - nachlaufgelenkt

You can find our complete vehicle inventory, including vehicles available for immediate and short-term delivery, on our website.
Excerpt from the equipment list.
Complete equipment list available upon request.

GOOSENECK
* Designed in SNT for optimized loading area length
* Length approx. 3,700 mm, with a rear slope of approx. 1,000 mm x 10°. For SZM: 4 x 2, 6 x 2, and 6 x 4.
* Front panel made of steel, plug-in type, approx. 400 mm high
* ASPÖCK-UNIBOX on the connection strip at the front with sockets
* 3 kW electro-hydraulic unit for controlling the hydraulic operations, with the exception of hydraulic winches
* Without installation of the supply connections on the SZM
* Outriggers on the gooseneck with mounting holes for screw-on lashing rings
* The first hole is approx. 200 mm from the front, followed by one every approx. 400 mm
* 2 pairs of screw-in lashing rings included (LC 5,000 daN)
* 1 pair of horizontal lashing rings in the rear area of the gooseneck (LC 10,000 daN)
* Approx. 40 mm thick hardwood deck above the gooseneck
* 2-inch kingpin
* Guide plate on the gooseneck for the turntable, approx. 500 mm wide
* 1 pair of recessed bolster pockets on the gooseneck for plug-in bolsters, approx. 100 x 50 mm

LOADING AREA
* In an extendable design, length approx. 8,800 mm with a slope at the rear of approx. 500 mm x 10°.
* A recess in the loading area and extending into the slope for accommodating the excavator arm, approx. 2,490 x 750 x 210/290 mm (L x W x H).
* TPMS tire pressure monitoring system according to ECE R 141.
* Mechanical landing gear with 2-speed gearbox and crank. JOST Module B
* Static test load = approx. 50,000 kg
* Continuous hardwood deck, approx. 50 mm thick, on the loading area and interrupted between the axles (this increases the coefficient of friction)
* 1 intermediate table, approx. 300 mm wide, for the extension tube with a large cross-section.
* 1 pair of fixed wheel recesses in front of the axles, open to the cross member of the gooseneck, approx. 700 x 410 mm (W x D)
* Wheel recesses with square ladder strips approx. 15 x 15 mm and widening in the lower area - 1 pair of fixed wheel recesses, approx. 1,480 x 700 x 410 mm (L x W x D), in the loading area between the 1st and 2nd axles. Wheel recesses with square ladder strips approx. 15 x 15 mm and widening in the lower area
* Aluminum covers for the wheel recesses in front of the axles and between the 1st and 2nd axles, which can also be used as widening boards (if the vehicle is equipped with extendable wideners)
* 1st axle with starting aid

BPW axles and suspension
* 1st and 2nd axles rigid, 3rd axle steered
* 3rd axle with electro-magnetic reverse lock via reverse gear and can be activated manually
* Technical axle load: 12,000 kg each
Ndodpfx Agozz Ei Re Dsc
* Air suspension with lifting and lowering valve.
* 235/75 R 17.5 3PMSF twin tires. Manufacturer of our choice

HYDRAULIC LOADING RAMPS
* DR-15/60-900-4350-HB-HV-M
* A pair of two-piece steel ramps
* with a length of approx. 4,350 mm and a width of approx. 900 mm. Hardwood deck
* Hydraulically folding ramp tips. Ramps can be individually shifted hydraulically outwards by approx. 235 mm and inwards by approx. 215 mm
* Maximum load and angle of inclination according to the technical data sheet: C465497
* In accordance with Regulation 2021/535/EU, ramps with a length of less than 300 mm do not need to be taken into account in the vehicle length of 16,500 mm in the driving position.
* Hardwood deck on the slope of the loadin

Annonsen ble oversatt automatisk. Oversettelsesfeil kan forekomme.