Arbeidsplattform semitrailer

FAYMONVILLE Telemax Megatrailer - hydr. gelenkt

Equipment Specifications

LOADING AREA
Gooseneck, length approx. 4,100 mm, with central beam. Loading area in extendable design, length approx. 9,400 mm, with rear taper approx. 350 mm x 10°, and integrated rail for attaching loose ALU loading ramps. Pneumatic locking with tapered locking pin and reinforced locking positions; supply lines are safely routed within extendable beams and automatically adjust to the respective loading area length.

Technical kingpin load: 18,000 kg
Suitable for tractor units: 4 x 2 and 6 x 2

- TPMS tire pressure monitoring system according to ECE R 141.
- BPW axles and suspension: all axles hydro-mechanically forced-steered, mounted on turntables.
Technical axle load: 12,000 kg each
Air suspension with raise/lower valve.
- 235/75 R 17.5 3PMSF twin tires. Brand of our choice
- ASPÖCK-UNIBOX
- 3 kW electro-hydraulic power unit for hydraulic operations.
(No installation of supply connectors on the tractor unit.)
- 4 pairs of recessed lashing rings in exterior frame of gooseneck:
- The three front pairs are horizontal (LC 10,000 daN).
- Rear pair is foldable outward (LC 10,000 daN).
Gujdpfey Augdsx Adyoa
- 4 pairs of stake pockets in exterior frame of gooseneck for plug-in stakes approx. 100 x 50 mm.
- 2 inch kingpin
- Mechanical landing gear with 2-speed gearbox and crank; JOST Modul B – static test load = approx. 50,000 kg.
- On gooseneck and loading area: approx. 32 mm wooden floor surrounded by ALU omega profiles.
- 10 pairs of recessed, foldable-outward lashing rings in the exterior frame of the loading area:
- Each 1 pair in front of last axle and on the trailer rear crossmember (LC 10,000 daN)
- All other lashing rings (LC 5,000 daN)
- 6 pairs of stake pockets in the exterior frame of the loading area for plug-in stakes approx. 100 x 50 mm.
- 1 spare wheel carrier under the loading area, right in the direction of travel.
- 1 lockable INOX toolbox, approx. 1,250 x 500 x 550 mm (L x W x H), mounted under the loading area, left in the direction of travel.
- Taper at the rear crossmember, approx. 350 mm x 10°.
- Integrated hanging rail for loose ALU loading ramps on the rear crossmember.
- 1 pair of drop-leg supports at the rear crossmember.
- Remote axle steering (front and rear) via cable remote control, with single-track monitoring, without installation in the tractor unit.
- Round NATO socket at the front connection plate (Maeler & Kaege VG 96 917)
- 1 LED work light each, left and right, mounted on the front wall, wired to the tractor unit interface.
- 1 locking position every approx. 500 mm on the extendable section.
- Storage bracket for plug-in stakes, inside front wall of gooseneck when not in use.
- 4 wheel chocks with holder under the loading area.
- Extendable (galvanized) widenings, approx. 230 mm per side (without wooden planks).
- 1 LED work light each, left and right, mounted in front of the axles, wired to the tractor unit interface.
- 2 axle load gauges mounted on the left side, including axle load diagram.
- First axle with traction aid.
- Under the gooseneck and at the rear crossmember left and right, each with a holder for warning signs.
- Acoustic warning signal when reversing.
- EU reflector at the rear of the vehicle.
- 1 LED reversing light each, left and right, at the rear of the vehicle.

Annonsen ble oversatt automatisk. Oversettelsesfeil kan forekomme.