Semitrailer med lavt lasteplan

Faymonville 6-Achs-Tele-Semi mit PA-X Achssystem

Gooseneck:
-Gooseneck in SNT design to optimize the length of the loading area, length approx. 3,750 mm, with a bevel at the rear of approx. 850 mm x 10°
-Can be raised and lowered hydraulically, stroke +- 250 mm including hydraulic connection connected to the hydraulic axle compensation of the first two axles
-Open in the rear third
-For tractor units: 6 x 4 and 8 x 4

Loading area:
-Loading area in extendable design, length approx. 11,000 mm with a bevel at the rear of approx. 500 mm x 10°.
-A recess in the loading area and in the bevel to accommodate the excavator bucket handle approx. 4,240 x 900 x 440 mm
-Pneumatic locking with conical locking bolt and reinforced locking positions, the supply lines are protected in the extendable supports and automatically adjust to the respective loading area length

Ramps:
-A pair of two-part steel ramps with a length of approx. 4,650 mm and a width of approx. 900 mm
-Hydraulically foldable ramp tips.
-Ramps can be moved individually hydraulically by approx. 235 mm outwards and approx. 215 mm inwards
-25 mm "Super Grip" rubber floor and approx. 5 mm sheet metal floor as additional reinforcement on the slope of the loading area
-20x30 mm square climbing rails, approx. every 200 mm on the outer frame of the ramp

Axles, suspension and tires:

-PA-X axle system, all axles hydro-mechanically forced steered
-The steering behavior of the first two axles can be optimally adjusted to the length of the loading area both mechanically and hydraulically.
-Hose rupture valve on the axle compensation cylinder with automatic RESET function.
-Hydraulic cylinder with shut-off valves and pins for securing in the raised position.
-245/70 R 17.5 3PMSF

Accessories included:
-Steel bulkhead, pluggable, approx. 400 mm high
-Connection strip for supply lines to the tractor unit, mounted at the height of the outer frame profile
-1 spare wheel
-Outer support of the gooseneck with mounting holes for screwable lashing rings
-The first hole approx. 200 mm from the front, then approx. every 400 mm
-2 pairs of screwable lashing rings included
-Checker plate covering above the gooseneck
-On the gooseneck 1 pair of pluggable aluminum side walls on the side, approx. 400 mm high, anodized
-On the gooseneck a pluggable aluminum rear wall, approx. 400 mm high, anodized
-3.5" kingpin / 2" kingpin mounted
-Guide plate from the gooseneck for the fifth wheel plate, approx. 500 mm wide
-4 Brake shoes
-4 axle load gauges
-Mechanical downpipe supports at the front
-1 one-piece INOX tool box, approx. 2,480 x 340 x 390 mm
-Mechanical downpipe supports at the front
-Continuous sheet metal covering on the loading area with a painted layer of sand to prevent slipping
-1 intermediate table, approx. 500 mm wide, for the pull-out, with long holes for hanging and movable bridging elements
-Painted sand coating on the support surfaces of the intermediate table
-Mechanical locking for locking the intermediate table to the pull-out
-8 pairs of stake pockets in the outer frame
-Extensions (galvanized) extendable by approx. 230 mm per side
-1 pair of hydraulic. Rear supports
-Central lubrication system
-1 reversing light on the left and right at the rear of the vehicle
-3 kW electro-hydraulic unit
-Widening planks, loose, in reinforced steel U-frame
Iedpfsk Af Svsx Aa Rjbd
-Radio and cable remote control
-4 warning signs, approx. 423 x 423 mm

Annonsen ble oversatt automatisk. Oversettelsesfeil kan forekomme.